The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old June 23, 1999, 05:15 PM   #1
Joe Portale
Senior Member
 
Join Date: June 8, 1999
Location: Tucson, Arizona Territory
Posts: 715
Hello all,

I have been having trouble with a Sprinfield 1911 pistol. It seems that no matter what I try, I can't get the gun to throw brass normally. After rounds are fired, the empty rounds fly 15-20 feet in every direction including straight up! I have rounded and polished the extractor head, tried taking some of the tension out by bending the extractor shaft away from the bullet, and even had the ejection port opened a little. Anyone have any suggestions? OBTW this is a stock gun with no added extras or after market things added, to my knowledge.

Joe P.
Joe Portale is offline  
Old June 23, 1999, 07:30 PM   #2
motorep
Senior Member
 
Join Date: October 29, 1998
Location: mid-coast Maine
Posts: 542
Did you check to see that the extractor had enough tension? If the case slips out of the extractor it can go in any (almost)direction. Also, you didn't mention the ejector, is it angled properly ? I kind of think I'd look at the extractor tension first, though. Oh yeah, is the hook deep enough ? (Thoughts coming in random order).
motorep is offline  
Old June 23, 1999, 10:01 PM   #3
Mal H
Staff
 
Join Date: March 20, 1999
Location: Somewhere in the woods of Northern Virginia
Posts: 14,518
Joe - I agree with motorep on extractor tension. Except for the port opening, the things you did may have made the situation worse. George will most likely have good advice on adjusting the extractor, but in general it should be able to hold a 230 gr round from falling when the slide is open and level. Weigand makes a good little guage to help with this adjustment. You can get it straight from him or from Brownell's.

If the tension is too light, who knows where the empty will be when it hits the ejector, if it does?
Mal H is offline  
Old June 23, 1999, 10:24 PM   #4
Mikey
Senior Member
 
Join Date: November 14, 1998
Location: Tennessee
Posts: 885
If the brass is going 15-20 feet then the recoil spring is almost certainly too light. I find the Wolf 18 1/2 pound to be about right for most 5" 1911's in 45 cal. I also think a full length guide rod aids in consistency but that may just be my opinion.

Mal H and motorep have pretty well covered the extractor/ejector topic.

Mikey
Mikey is offline  
Old June 23, 1999, 10:28 PM   #5
George Stringer
Staff Alumnus
 
Join Date: October 12, 1998
Location: Earlington KY
Posts: 2,299
Joe, if you go to www.m1911.org you will find a link to tecnical issues. There Bill Wilson discusses adjusting the extractor. It seems like I answered this question yesterday somewhere else, but on the face of it, with all things being equal, your recoil spring is too light for the load you're using. Try going up a pound or two. I normally don't recommend this but, if you have a stock ejector, not a commander type, then your recoil spring is not doing it's job to protect your frame. George
George Stringer is offline  
Old June 23, 1999, 10:28 PM   #6
zot
Senior Member
 
Join Date: April 2, 1999
Location: U.S.A.
Posts: 566
weak recoil spring, premature slide opening,
barrel might not be locking right,is the
"normal" way brass should fall just to the right and slightly behind you??? I usually get one on the top of the head, are you shooting mil-spec or reloads or +P ? is gun
new or old? what do cases look like? so many
things, weak firing pin spring could hang up
pin and would knock case different,CCI aluminum cases , ejector might be wrong angle
or worn out. my $3.39 worth:}
zot is offline  
Old June 24, 1999, 11:01 AM   #7
Joe Portale
Senior Member
 
Join Date: June 8, 1999
Location: Tucson, Arizona Territory
Posts: 715
Thanks for all the suggestions. I believe that the extractor angle/tension is correct. I will pickup a new recoil spring today and see what that does. Also, I heard that a common fault with Springfields is that the factory extractor is too long. Anyone else
hear this?

Thanks

Joe
Joe Portale is offline  
Old June 24, 1999, 08:24 PM   #8
HankL
Senior Member
 
Join Date: March 11, 1999
Location: The Sunny South
Posts: 2,174
Joe, Thinking on all of the above, please tell us exactly what you are fireing in this puppy. It would help all of the folks who are trying to help you.
Sound's to me like hot load, weak spring, and burr somewhere. IMHO Hank
Have fun, be safe, and stay knee deep in brass!
HankL is offline  
Old June 24, 1999, 10:05 PM   #9
Joe Portale
Senior Member
 
Join Date: June 8, 1999
Location: Tucson, Arizona Territory
Posts: 715
For those who asked, I'm rolling mine own. I shoot 230 grain lead round nose in front of 5.0 grains of Red Dot. These rounds chrono out between 875 and 900 feet per second. It is a stout load, but not what I would consider hot.

Today, I replaced the recoil spring and released some of the tension on the extractor. These changes helped a lot! Thanks to all. I'm still open to suggestions or comments.

Joe
Joe Portale is offline  
Old June 25, 1999, 01:55 PM   #10
leapfrog
Senior Member
 
Join Date: January 19, 1999
Location: Texas
Posts: 107
My experience has been that the Wolff Variable Power 18 1/2 lb. recoil spring is the way to go with all full power loads. If I were shooting a steady diet of +P rounds, be sure to put a shock buff in the gun, at least for practice. I also concur with Mal H, the Weigand tool for adjusting extractor tension is worthwhile.
leapfrog is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:30 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07858 seconds with 9 queries