The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old May 17, 2005, 08:06 AM   #1
AustinMike
Senior Member
 
Join Date: October 25, 2004
Location: Austin, TX
Posts: 171
Rainier 200gr. SWC .45 loads?

I just ordered some Rainier 200gr. SWC .45's to try. I've shot their 230gr. RN for years and like them a lot, but wanted to give the clean hole punchers a try. Anybody got any loads to share? I want loads that are around 850fps for IPSC use. I've got Clays on hand and I can get HP-38 and Titegroup real cheap here.
AustinMike is offline  
Old May 17, 2005, 08:32 AM   #2
Jim Watson
Senior Member
 
Join Date: October 25, 2001
Location: Alabama
Posts: 10,892
Pardon me for not getting up and looking up specific "recipes" for you, but I just loaded them like 200 grain cast. The powders you list are fine. It will take a maximum load of plain Clays to make Major, you have more margin of safety with HP38 or Titegroup.

Be sure your sizing die is tight and your expander is small, I had trouble with them setting back against the feed ramp where cast and jacketed bullets did not. I also had trouble getting them to feed in guns set up for the No 68 cast SWC. So I don't load plated bullets any more. Good luck.
Jim Watson is offline  
Old May 18, 2005, 07:14 AM   #3
BigDog(RE)
Member
 
Join Date: January 16, 2005
Location: Miami, FL
Posts: 41
There is some good load data here: http://www.rainierballistics.com/loaddataMW.htm

I use them with 5.5gr of W231, and I like the end result.
BigDog(RE) is offline  
Old May 18, 2005, 10:21 AM   #4
Johnny Guest
Moderator Emeritus
 
Join Date: August 28, 1999
Location: North Texas
Posts: 4,116
My favorites - -

Sorry I can't help you with the powders you mention.

With that or similar bullets, I have variously used - - -

Unique, 6.2 to 6.5 gr. ~830 to 860
H. Universal, 6.5 gr. ~ 850
W-231, 5.6 gr. a bit less - - perhaps 775 or so, but quite accurate in my pistols.

The original H&G #68 bullet was designed to have the shoulder and the edge of the meplat as points of congruency with the 230 FMJ bullet. If you have the nose stem in your seating die set to duplicate factory hard ball, you should be good right there. Speer manual says COL should be 1.275".

Best of luck
Johnny
__________________
MOLON LABE!
Amendment II ensures the rest of the Bill of Rights.

Blog: Expert Witness
Johnny Guest is offline  
Old May 19, 2005, 01:23 AM   #5
Mark whiz
Senior Member
 
Join Date: May 19, 2004
Location: Wabash, IN
Posts: 227
By far, my best load with that bullet (for my SA 1911-A1 Mil-Spec) is 9.6gr of AA#5 loaded to an OAL of 1.258". These will cut the same hole all day long at 15yds - they run 903fps,with very little deviation.

My next best loads are:
4.7gr of Win Super Target (WST)
5.3gr of Win 231

each of those loads group an inch larger than the previous one.

Win231 is said to be the same powder as HP-38 (although some disagree), but you might want to try the HP-38 starting at 5.0gr & working up toward 5.5 & see what you get
__________________
"Every moving thing that liveth, I give unto you as meat" (Gen 9:3)
Aim small.........miss small.
Trust God..........but keep your powder dry
!
Mark whiz is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:58 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08434 seconds with 9 queries