The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old March 2, 2005, 11:20 PM   #1
Bass Man
Member
 
Join Date: December 26, 2004
Location: Missouri
Posts: 92
Do you check your powder measure?

Do you, and how often do you check the loads your powder measure is throwing?
Bass Man is offline  
Old March 2, 2005, 11:29 PM   #2
redrooster2
Member
 
Join Date: September 23, 2004
Location: north of Acadiana
Posts: 80
I'll check about every 10th round when loading for pistols but usually check every round when loading for rifles.
redrooster2 is offline  
Old March 2, 2005, 11:47 PM   #3
Bass Man
Member
 
Join Date: December 26, 2004
Location: Missouri
Posts: 92
Do you ever catch your charge being off?
Bass Man is offline  
Old March 3, 2005, 12:06 AM   #4
Throckmorton
Senior Member
 
Join Date: May 22, 2004
Location: Washougal,Wa
Posts: 126
Since I use a progressive I triple check the first load or two,and just occasionaly after that.I never find enough variance to worry about...plus or minus a tenth or two.
I'd hate to have to pull seveal hundred bullets,so I make triple sure at the beginning of the run.And yes,even then I"ve messed up..you've got to double/triple check that the load is what the book says,not what you 'rememeber.'
Throckmorton is offline  
Old March 3, 2005, 12:29 AM   #5
Scott5
Senior Member
 
Join Date: November 25, 2004
Posts: 132
I have a Lee Pro 1000 that I use for pistol, and I check it untill I get it set where I want it and it stays right there.

For rifle I used to use a single stage RCBS and hand weigh each charge then got a D550B, and still had to hand weigh each charge. (I called Dillon two times about there powder drop. It would be off up to 2gr.)
Then I bought a Lyman 1200DPS and use that to weigh each charge in rifle.

Happy shooting
Scott5
Scott5 is offline  
Old March 3, 2005, 01:26 AM   #6
Leftoverdj
Senior Member
 
Join Date: October 15, 2004
Posts: 934
Depends. On a pistol charge with a known load and a fixed chamber measure, I might not check it at all. I already know what it throws and it ain't gonna change.

On an adjustable rifle measure, I might weigh ten charges before I drop the first one into the case. If the charges are dropping uniformly, I ain't gonna weigh another until the last one into the block. That's just to check that nothing has moved in the 50 cartridges. If the charges won't drop uniformly, I might weigh every one and trickle as needed.

Works for me, but I ain't one for raggedass max charges.
Leftoverdj is offline  
Old March 3, 2005, 08:42 AM   #7
lee n. field
Senior Member
 
Join Date: October 12, 2002
Location: The same state as Mordor.
Posts: 3,415
After inspecting visually for obvious problems, I'll weight 2 or 3 randomly selected cases out of a loading block of 50.
lee n. field is offline  
Old March 3, 2005, 09:10 AM   #8
HSMITH
Senior Member
 
Join Date: June 21, 2002
Posts: 2,019
It depends on the powder and the load. Some powders meter with boring accuracy and some don't. My Dillon and Redding measures are very good compared to the others I have owned.


How often I check also is determined by the powder and load. Light loads with Bullseye never vary enough to be seen on my scale. Extruded rifle powders vary quite a bit, up to .3 grains each way.
HSMITH is offline  
Old March 3, 2005, 10:43 AM   #9
larryf1952
Senior Member
 
Join Date: July 17, 2004
Location: KCMO
Posts: 476
I load only for handguns. After I find the setting that gives me the desired charge weight, I'll weigh 5 or 6 rounds in a row to verify consistency. If I'm getting consistent charges, I'll not check it again until the next 100 rounds.

I've also adopted a policy of using only ball or small flake powders. Herco used to be a favorite powder of mine for 9mm, but the flakes are so large that I was having to set the powder measure for a light throw, then trickle each round to make correct weight. Too tedious.
larryf1952 is offline  
Old March 3, 2005, 11:03 AM   #10
BillCA
Senior Member
 
Join Date: November 28, 2004
Location: Silicon Valley, Ca
Posts: 7,087
I load primarily for handguns. What I do is find the right weight and set the locking ring. Then I'll throw 3 charges and weigh each. If I'm using something other than ball powder (which measures very uniformly) I'll throw another 3 charges into the pan at one time and weigh it. It should be exactly 3 times the single-throw charge. I'll do this especially when switching powders or using an extruded powder like IMR bar powders.

For bar powders, I'll weigh each charge until I'm comfortable with the accuracy of each one. Then measure every 3rd one to ensure consistency.

Like Leftoverdj, I'm not one for loading max charges either.
__________________
BillCA in CA (Unfortunately)
BillCA is offline  
Old March 3, 2005, 12:46 PM   #11
30Cal
Senior Member
 
Join Date: December 3, 2002
Posts: 1,106
I check every 5th-10th charge when using my Dillon progressive after things are up and running. The only time I measure each charge is when I'm making my 600yd loads for Highpower--I don't bother for the short line loads (200 and 300yds). +/- 0.3grs variation is tough to see on paper and still shoots inside 1MoA in my match rifle.

I recently got a Harrell powder measure and find that I really don't need to be checking my 600yd loads anymore.

Ty
30Cal is offline  
Old March 3, 2005, 01:11 PM   #12
road.warrior
Member
 
Join Date: October 22, 2004
Location: Wallyworld, CT
Posts: 26
Every charge, every caliber.

I only do small runs, so I am looking for precision, not quantity
on a single stage press.
road.warrior is offline  
Old March 3, 2005, 04:52 PM   #13
G56
Senior Member
 
Join Date: June 10, 2004
Location: Oklahoma
Posts: 302
I run a Dillon RL550, I always double, triple check the powder measure at the start of any loading session, I have never found it to be out of adjustment, but I still check it, every time.
__________________
John
G56 is offline  
Old March 3, 2005, 05:07 PM   #14
Russ5924
Senior Member
 
Join Date: February 18, 2005
Posts: 1,874
I"m like G56 I always cheak at the start to make sure I have the right grains dialed in,then I stop and check every 25 rounds or so to make sure the powder drop is working.My Dillon has never changed while reloading but guess the powder drop could plug.
__________________
Russ5924
Russ5924 is offline  
Old March 3, 2005, 05:54 PM   #15
tjhands
Senior Member
 
Join Date: January 20, 2005
Posts: 1,710
I'm just new to this fun hobby, but I check the powder on the scale every 10th pull or so. Hasn't been off at all yet.
tjhands is offline  
Old March 3, 2005, 08:10 PM   #16
donkee
Senior Member
 
Join Date: November 7, 2004
Location: Mid-Michigan
Posts: 431
ditto redrooster2.......
donkee is offline  
Old March 3, 2005, 08:25 PM   #17
Guy B. Meredith
Senior Member
 
Join Date: August 29, 1999
Location: Salem, Oregon
Posts: 1,578
I run a few to bounce the machine a bit and make sure the powder is settled as much as it will (have never compared to find out whether this is necessary or not--less time consuming to just assume it does). I then weigh 3 or 4 loads and maybe one about 50 down the line.

The Hornady is boringly consistent for revolver loads. I have found that different batches of the same powder will weigh differently and, too, want to make sure I haven't accidentally miss adjusted something.
Guy B. Meredith is offline  
Old March 4, 2005, 12:14 AM   #18
Austin Charles
Member
 
Join Date: December 16, 2004
Posts: 32
I check my RCBS about every 25. I have one of those micro adj. , and that thing is alway's right on the money. The thing amazes me

I use the RCBS for fine powder, then I use my Lee for stick powder. Both are dead nut 99% of the time.
Austin Charles is offline  
Old March 10, 2005, 10:56 PM   #19
cheygriz
Senior Member
 
Join Date: May 11, 2002
Location: high up in the rockies
Posts: 2,232
On my Dillon 650, I check every 100 rounds. When I refill the primer tube, I check a charge. It probably isn't necessary to check a Dillon that often, but it gives me a warm fuzzy feeling.
__________________
If you think a mighty military force is expensive, wait 'til you see what a weak one costs.
cheygriz is offline  
Old March 11, 2005, 12:14 AM   #20
cuate
Junior member
 
Join Date: February 18, 2005
Location: Comanche Co. Texas
Posts: 737
Powder Measure Check

I weigh every charge on an electronic scale, under charge a tad and bring to desired weight with a powder trickler.
This is for rifle cartridges, pistols about every tenth round and shotshells until I get the charge within .1 or so and not again that reloading session.
cuate is offline  
Old March 11, 2005, 12:47 AM   #21
yorec
Senior Member
 
Join Date: February 2, 2000
Location: Wyoming
Posts: 2,324
Depends on what ammo I'm producing - but always check at the beginning and end of every session - and usually every two hundred rounds If I'm using my Dillon. If I'm using a single stage press with my RCBS, every hundred rounds.

But if I'm trying to produce superaccurate loads - I'll weigh each one.
__________________
What part of "... shall not be infringed..." don't you understand?

My site - stop by n see what I'm all about... Yes, there is gun stuff.
yorec is offline  
Old March 12, 2005, 08:12 AM   #22
WESHOOT2
Senior Member
 
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,270
one Hornady/Pacific, fifteen Dillons

First I set up my RCBS 505 using check weights. Always. As in "without exception". I mean always.
Then I check the first ten, or wait until the charge weight stabilizes and then check ten.

Then, every so often, I recheck. Not ten-or-twenty, just when I feel hinkey; know what I mean?
In the few rds I've made, none of my measures varies enough to be significant.
I don't normally try to use 700X or Unique in my Dillon; know what I mean?
__________________
.
"all my ammo is mostly retired factory ammo"
WESHOOT2 is offline  
Old March 15, 2005, 10:28 PM   #23
norielX
Senior Member
 
Join Date: January 10, 2001
Location: Texas
Posts: 164
Yes.

I'm loading on a single stage with the batch method. I throw around 10 charges (or more) to get the measure ready, then I throw and measure another 10 to check consistency. I'll generally check every 10 throws to make sure nothing's moved. With as little time as it takes to throw and weigh, at least for single stage, why wouldn't you want to check your measure? The point is making SAFE ammo, not a lot of iffy rounds.
__________________
-- norielX
norielX is offline  
Old March 21, 2005, 10:34 AM   #24
highteckredneck
Member
 
Join Date: February 16, 2005
Location: Loogootee, Indiana
Posts: 36
I weigh EVERY charge. I only use the thrower to get close as it frequently varies by 1/2 grain. When weighing the charge you will be within 1/10 grain with most scales.
highteckredneck is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:44 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.12822 seconds with 9 queries