The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old March 19, 2005, 11:00 AM   #1
Rodger Peterson
Member
 
Join Date: December 18, 2004
Location: Nevada
Posts: 93
Powder measure suggestions

I am going to invest in a quality powder measure. I would appreciate an feedback from those of you using the Redding, RCBS, or Hornady brands. I've been eyeballing the Hornady unit, but really can't say why. I need to measure from 3.0 to 56. grains. I relize I may have to purchase inserts. I'm loading on a single stage press. Powders will be Unique, IMR4350, W231, W748, Blue Dot, W760, WSF. Thanks in advance.
Rodger Peterson is offline  
Old March 19, 2005, 11:09 AM   #2
Jim Watson
Senior Member
 
Join Date: October 25, 2001
Location: Alabama
Posts: 11,025
I use a RCBS Uniflo with small drum and micrometer spindle for most single stage loading. It does take two strokes to drop 50 grain rifle charges, though.
I have a Redding No 3 Master that is good on rifle loads but the insert with pistol plug was never very good. It did not fit well enough to keep granules from getting around the insert and binding up the rotation. So I put a metal hopper on it and use it for black.
The funny looking Bonanza does ok from about 8 grains up, I have not tried it with light target pistol loads.
Jim Watson is offline  
Old March 19, 2005, 01:36 PM   #3
Swamp Yankee
Senior Member
 
Join Date: November 26, 2000
Location: Northeastern Ct.
Posts: 1,013
For the money it's tough to beat a Uniflo.
I've run all the listed powders with the exception of the IMR4350 through my Uniflo with the standard cylinder and have no complaints. It's very repetative.
I've used a Redding and it is indeed a very nice measure. It's also close to double the cost of the Uniflo however.
No experience with Hornady's offering.

Take Care
Swamp Yankee is offline  
Old March 19, 2005, 02:46 PM   #4
WESHOOT2
Senior Member
 
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,213
buy a good one

I have the Hornady/Pacific measure set up for handgun-only charge weight ranges.

Can bind a bit on AA9 LOL.


(I have fifteen Dillon measures; they can, too.)
__________________
.
"all my ammo is mostly retired factory ammo"
WESHOOT2 is offline  
Old March 19, 2005, 04:04 PM   #5
Dave R
Senior Member
 
Join Date: January 7, 2000
Location: Idaho
Posts: 6,073
I use a RCBS Uniflow with the small drum for pistol loads through .223. Its very accurate, even with big-flake powders like Unique.

For rifle loads, I use the large drum with the Uniflow. Also very accurate, even with stick powders like 4197 or IMR 4064.

I bought the Uniflow used. It came with the small drum. I called RCBS to order the big drum, and they sent it for free.
__________________
I am Pro-Rights (on gun issues).
Dave R is offline  
Old March 19, 2005, 04:52 PM   #6
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 35,892
I've got a lot of loads through my Lee disk measure. It's always done fairly well by me.

I've also got my RCBS Uniflo, which is a great piece of equipment.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Old March 19, 2005, 08:07 PM   #7
justnuts
Junior Member
 
Join Date: February 18, 2005
Location: Olympia, WA
Posts: 5
I have a Hornady powder measure. It makes a fine door stop
__________________
Member NRA
Member Washington Arms Collectors
justnuts is offline  
Old March 19, 2005, 08:22 PM   #8
klw
Senior Member
 
Join Date: February 27, 2005
Posts: 118
If money is no object

Harrell's are unquestionably the best (http://www.harrellsprec.com/). I've got two. I've also had the others you mentioned.

It depends a bit on the application but Lyman's is fine. The RCBS units are certainly ok. The rest, well, I didn't care for them that much.
klw is offline  
Old March 20, 2005, 09:57 PM   #9
Rodger Peterson
Member
 
Join Date: December 18, 2004
Location: Nevada
Posts: 93
Thanks for the replies, looks like the Uniflo is getting the nod.
Rodger Peterson is offline  
Old March 20, 2005, 10:28 PM   #10
Ala Dan
Member in memoriam
 
Join Date: August 13, 1999
Location: In The HOT, Humid, and Mu
Posts: 6,116
Greeting's All-

I use a RCBS Uniflow, complete with a homemade baffle. I took
an old washer with 'bout a 5/16" hole (to control the powder flow)
and it works perfectly with all types of powders.

Best Wishes,
Ala Dan is offline  
Old March 20, 2005, 10:40 PM   #11
Oldphart
Senior Member
 
Join Date: May 19, 2004
Posts: 375
Powder measure suggestions

Rodger, I'm sitting here looking at the latest Sinclair catalog. They devote a page to Harrell measures. As I read all the information there, I see stuff about "CNC machined aluminum body" and "needle bearings" and price tags that run from $173 to $234. What I don't see is any comparative claim regarding accuracy. While they do say the Harrell is accurate and repeatable, they don't say how accurate.
I have to admit that I've only used one brand of powder measure, but I've never seen any reason to change either. After a 'break-in' period, it now throws loads consistently within 0.1 grain of whatever load of whatever powder I happen to be using. Since I'm retired, I have the time to check more loads than you might, so I check about every third load. For the past year or so, I have rarely found any appreciable variation from my desired load.
I use one of those plastic POS's by Lee. It came with my original Anniversary kit and the only thing I've done is get a second one for smaller loads. Either one will measure large or small loads but making the adjustment is a pain. I can get ten of them for the price of one Harrell...
Oldphart is offline  
Old March 20, 2005, 10:54 PM   #12
Tim R
Senior Member
 
Join Date: November 30, 2004
Location: God's side of Washington State
Posts: 1,601
The RCBS Uniflow has served me well for the last twenty years. When I bought mine, they came with both the large rifle drum and the small pistol drum. I understand this is not the case any more but I also understand a call to RCBS will get you the other drum at no cost to you. Both are handy depending on what you are doing.
__________________
God Bless our Troops especially our Snipers.
Tim R is offline  
Old March 21, 2005, 03:33 AM   #13
CaseyC
Member
 
Join Date: November 29, 2004
Posts: 19
Rodger,

I have a Hornady, a RCBS, and a Harrrell's. All three measure ball powder well, the Harrell's the most accurate of the three. None of them measure extruded powders well, the Harrell's being slightly better of the three. With stick powders, I set the charge .5-1gr lower and trickle the remainder.

Casey
CaseyC is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:13 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09414 seconds with 9 queries