The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old February 28, 2005, 07:46 PM   #1
supercharged3800
Junior Member
 
Join Date: February 28, 2005
Posts: 1
Lee 3 or 4 hole turret?

I have decided to start off with the lee auto-indexing turret press. I just have to decide on the 3 or 4 hole. I'm leaning towards the 3 hole since I'll mostly be doing handgun calibers for now and this will save a step, but I'm looking for opinions on what other people prefer.
supercharged3800 is offline  
Old February 28, 2005, 08:52 PM   #2
sindiesel666
Senior Member
 
Join Date: November 17, 2004
Location: San Antonio
Posts: 270
4-hole all the way...lotsa more flexibility.
What calibers you shooting???? I loaded for 45 ACP (for my CZ-97B) on my 3 hole until I bought a Dan Wesson 1911 with a really tight chamber. At least once in 10 rounds I'd have a jam because rounds were slightly large for the chamber. I bought the Lee factory die and the 4-hole conversion and since then no problems whatsoever.

Plus, I just got the Dillon 650, just moved my dies and I was set....
sindiesel666 is offline  
Old February 28, 2005, 09:08 PM   #3
Lycanthrope
Senior Member
 
Join Date: October 1, 2001
Location: PA
Posts: 1,752
It's really nice to seat and crimp at different stations.....

4 hole.
Lycanthrope is offline  
Old February 28, 2005, 11:20 PM   #4
rwilson452
Senior Member
 
Join Date: June 10, 2004
Location: Tioga co. PA
Posts: 2,364
4 hole

For reasons stated, four hole for sure. Either that or get an extra turret and put the sizing die in it. Me, I use a 5 hole Loadmaster and use them all. ( one hole for priming).
rwilson452 is offline  
Old February 28, 2005, 11:58 PM   #5
Oldphart
Senior Member
 
Join Date: May 19, 2004
Posts: 375
Lee 3 or 4 hole turret?

In the end, it'll depend on your particular needs. I started with a 4-holer but found I didn't really need the extra station so I traded for a 3-holer. Also, I mounted my press on the left end of my bench, so I needed to access the shellholder from the right side. The 4-holer didn't permit me to do that since the front vertical post was in the way and couldn't be moved like the 3-holer can.
Oldphart is offline  
Old March 1, 2005, 10:53 AM   #6
sundog
Senior Member
 
Join Date: November 22, 1999
Location: Green Country, OK
Posts: 730
Kinda depends on wether you're gonna size and decap on station 1. I size/decap on a single stage, bacause it gives me a chance to inspect each piece of brass. Then I prime with a hand primer and store the primed brass until ready for loading, that way I can make up any load I want and not have to wait until I shoot a bunch to reclaim brass - got plenty primed brass on hand all the time, but only the ammo I'm expecting to shoot near term. Anyway, another reason I got into doing this is because I do NOT like the priming mechanism in the Lee turret press at all. So, with brass already primed, first station is powder/flare, second is bullet seat, and third is crimp (better ammo with seperate seat and crimp, I think). Now, if your going to do the whole cycle including size/decap, then go with the 4-holer. I have one of each and they both work fine. Or if you want to hand prime, just use the 3-holer as a single stage for just sizing/decapping. You could even mount 3 sizer dies in one turret for 3 different calibers, and set up 3 other turrets with the rest of the dies for each caliber. sundog
__________________
safety first
sundog is offline  
Old March 1, 2005, 01:03 PM   #7
Russ5924
Senior Member
 
Join Date: February 18, 2005
Posts: 1,874
I would say a 4 since I have one.But if you get a 3 holer you can get the conversion to a 4 hole. But they don't sell a kit to go from 4 to 3 at least never saw one.for some starting out I don't think you can go wrong with what you are buying.It is simple to use the only way to get in trouble is if you don't move the lever full down and up then it won't index.And if you are on the powder station
__________________
Russ5924
Russ5924 is offline  
Old March 16, 2005, 10:32 PM   #8
cuate
Junior member
 
Join Date: February 18, 2005
Location: Comanche Co. Texas
Posts: 737
Lee 3 or 4 hole turret?

We used a 3 holer for a long time loading .45 Long Colt for Cowboy Action Fun. Ordered a 4 holer, best I recall it fit right in. Now reloading 30-40 Krag and 30-06 and four holes weren't enough for both sets of dies. Now using a 6 holer Lyman, massive, heavy duty and should last a lifetime.

Redding or somebody has a seven holer out......................
cuate is offline  
Old March 16, 2005, 10:37 PM   #9
Lennyjoe
Senior Member
 
Join Date: June 28, 2001
Location: Sunny Tucson Arizona
Posts: 1,148
I use a 4 hole turret for pistol rounds. I also use a seperate die for crimping instead of the seating die. For 45 and 10MM I use a factory crimp. The 4th hole is nice for the additional crimp dies.
__________________
If you see a Military man or a Vet, stop him and say "Thanks".
Lennyjoe is offline  
Old March 17, 2005, 12:14 PM   #10
karpins
Junior Member
 
Join Date: March 13, 2005
Posts: 4
I have a Lee Loadmaster, been using it for about 2 weeks.
It is a 5 turret top of the line Lee progressive press.
The Loading experts will recommend three presses for their best choice, a Dillon, Dillon, or a Dillon.

While I cant afford one of these yet, I settled on a top of the line Lee Loadmaster ready to go for .45acp for $210 and I have not been at all disappointed.
karpins is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:38 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08857 seconds with 9 queries