|October 1, 2004, 09:23 PM||#1|
Join Date: October 1, 2004
Location: Remote Utah desert
How to Properly Use a Cap & Ball Revolver
So you have a new cap and ball revolver?
Here's how to wring the best accuracy from it. You’ll want to print this out, it’s long and will require frequent referral.
Buy some JB Bore Compound or Iosso Bore cleaner. These are pastes, very mildly abrasive, designed to clean bores without harm. Put this paste on a patch that fits snugly and work it back and forth in the bore until the patch becomes a loose fit (usually six to 8 passes).
Do this at least a dozen times. This will remove factory preservatives and help smooth the bore somewhat.
If the chambers are rough, this may also be done but do so by hand. Resist the temptation to chuck your cleaning rod in a drill; you can too easily enlarge the chamber.
After the bore or chambers are smoothed, remove the paste with patches wet with Ronson lighter fluid. Lighter fluid evaporates without leaving behind deposits.
BLACK POWDER IS BEST
In my experience, FFFG black powder has been the most accurate propellant in .36 and .44-caliber revolvers. I've tried FFG and Pyrodex P and not found it as accurate.
Use Wonder Wads, as sold by Ox-Yoke, or punch your own wads from stiff felt. A 3/8 inch punch is perfect to create .36 caliber wads. Use a .45-caliber wad punch for the .44 revolvers. In metric, this would translate to about 9.5mm and 11.25mm wad punches.
Old cowboy hats are a good source of stiff felt. Look in thrift stores for old hats. Some hardware stores sell wool felt on a roll, for use as window insulation. Whatever the felt, it should be at least 1/16th of an inch thick and preferably 3/8 inch.
Don't use the felt sold in hobby shops, as it's too limp. Check the label on the felt, much of it is partly or wholly polyester (plastic) which will deposit melted plastic in your bore.
If you’d rather not bother, Wonder Wads are okay but do not use them as-is. In my experience, they lack sufficient lubricant to work properly. Soak the wads in melted lard, mutton tallow, bacon grease or any other natural (animal or plant) grease. Don’t use petroleum greases, they create a hard, tarry fouling when mixed with black powder.
BEST WAD LUBRICANT
The best wad lubricant I've found is listed in a 1943 American Rifleman magazine. It is made of:
1 part paraffin (I use canning paraffin, sold in grocery stores)
1 part mutton tallow (sold by Dixie Gun Works)
1/2 part beeswax (available in hardware stores as a toilet gasket)
All measurements are by weight, NOT volume.
I use a kitchen scale to measure 200/200/100 grams of ingredients, which will nearly fill a quart, wide mouth Mason jar.
With the jar filled, place it in three to four inches of boiling water (the safest way to melt greases and waxes) until all ingredients are thoroughly melted. Stir with a clean stick or disposable chopstick.
Allow the lubricant to cool at room temperature. Placing the jar in the refrigerator may cause the ingredients to separate. When the lubricant is cool and solid, screw the jar lid down tight and store it in a cool, dry place. This will keep dust and crud out and keep natural moistures in.
This lubricant is also excellent for other black powder applications: patch grease, lubricating fiber shotgun wads and as a bullet lubricant in muzzleloaders or cartridge guns.
In fact, it’s all I use. I no longer buy commercial black powder bullet lubricants such as SPG or Lyman Black Powder Gold. This recipe is as good or better and much cheaper.
Canning paraffin is the hard, translucent wax sold to melt and pour over preserves, such as jams and jellies. Use canning paraffin only. Who knows what’s in old candles, especially the scented variety? But if old candles are all you can find, use them.
Some sharp-eyed black powder shooters may see paraffin among the ingredients and gasp because paraffin is a petroleum product, and petroleum products cause hard, tarry fouling. However, a chemist told me that paraffin lacks the hydrocarbons of other petroleum products, which appears to be the offender.
The paraffin is necessary in this recipe because it stiffens the wad, which helps it scrape fouling from the bore.
Sold by Dixie Gun Works in Tennessee, you may also find it if you live in sheep country. Mutton tallow makes a superior product. I’m told that unlike beef lard and other tallows, mutton tallow contains lanolin. I’m unsure about this, but it makes a difference in the lubricant.
For about 100 .36 or .44 caliber wads, melt two or three Tablespoons of lubricant in a clean tuna can at a low temperature. There's no need to cook the lubricant, just melt it. Add the wads. Stir them in the melted lubricant until thoroughly saturated. Cool at room temperature.
I carry the wads to the range in the same can, with a plastic pet-food lid snapped on. Store them in a cool, dry place with the lid snapped tightly.
USE A LOADING STAND
A loading stand that holds the revolver upright on the range table is best. It allows you to get a better "feel" for how much pressure you're applying to the wad and projectile. It also holds the revolver securely in an upright position if you need to interrupt the loading process.
Add a measured powder charge to each chamber.
I've found that 20 grs. of FFFG is a good starting load in my .36 caliber Colt Navy and Remington, and 30 grs. is good in the Remington and Colt .44 revolvers. For the 1862 Colt Pocket in .36-caliber, use 15 grains of FFFG.
Place a lubricated wad over the mouth of each charged chamber, then thumb-press the wad slightly below the mouth of the chamber. Now, seat each wad firmly onto the powder charge. Don't crush the powder; just seat the wad firmly against it.
There are good reasons for seating the wad separately. First, should you forget to add powder to the chamber, it's easier to remove a felt wad than a stuck ball. Secondly, this gives you a better feel for how much pressure you're applying. Thirdly, it makes it easier to seat the ball.
Use a .380 inch ball for the .36 caliber, and a .454 or .457 inch ball for the .44 revolvers (the Ruger Old Army requires a .457-inch ball).
I purchase .380 inch, sprueless balls from Warren Muzzleloading at www.warrenmuzzleloading.com so I don’t' have to deal with the sprue left from cast balls.
If you use cast balls, the sprue must be up and centered before ramming.
Many black powder manuals suggest .375 and .451 inch balls for these revolvers but they typically are not as accurate. The larger balls create a wider bearing surface for the rifling to grip, which aids accuracy.
CORN MEAL FILLER
For less than maximum loads, I sometimes use a little corn meal on top of the wad. Wipe it slightly below flush with your finger. Use corn meal; Cream of Wheat does not compress so it's not as forgiving if you add too much. The use of corn meal is not mandatory but for light loads it’s suggested.
With wads seated firmly on the powder in each chamber, it's time to seat the ball.
With the rammer, seat the ball firmly on the wad. The ball should be large enough that the chamber shaves a ring from it.
If you don't get a ring of lead, it may be that your chamber mouths are so chamfered that a ring is not cut, or that you need a larger ball.
Seat the ball firmly into the chamber. If the first ball takes too much pressure to push in below flush, add less corn meal to the other chambers.
The ball should be seated just slightly below flush of the chamber. If it is seated too far into the chamber, the ball has a long jump before it engages the rifling in the forcing cone. This long jump can affect accuracy.
The ball MUST be seated firmly onto the wad, or corn meal if you use it. There must be NO space between ball, wad, corn meal (if you use it) or powder. A space creates a dangerous condition that may markedly increase pressures.
By using a lubricated wad, grease over the ball is not usually needed. I live in the Utah desert where temperatures may get to 110 degrees Fahrenheit (43.5 Celsius) with less than 6 percent humidity. On such days, I've found it useful to add lubricant over the ball but these days are not frequent so I rarely do so.
The same lubricant as used for the wads may be smeared over the ball with a Popsicle stick, to avoid messy fingers.
I’ve yet to find a conical bullet as accurate as a lead ball. The Lyman 37583 bullet, intended for the .38-55 rifle, is often used for .36 caliber revolvers but it’s hard to seat straight. This is a common problem with many conicals. They lack a rebated rim that will slip into the chamber and align the bullet before ramming.
The Lee and Buffalo Bullet designs have this rim but I still haven’t found them as accurate as a ball. Conical bullets must be lubricated before seating. The above lubricant works quite well, or you can use Crisco, Bore Butter or my favorite commercial lubricant, CVA Grease Patch.
With all balls seated firmly in the cylinder, it's time to cap the revolver. I like Remington No. 10 or 11 caps in my revolvers but use CCI on occasion. The Remingtons fit my revolvers' nipples better .
I can't tell you which size cap to use; you'll have to find that through trial and error on your nipples. The cap should fit snugly on the nipple, and "bottom out" so that the tiny bit of priming compound in the cap rests against the cone of the nipple. If it doesn't go down this far, use the larger cap.
If the cap is loose on the nipple, use the smaller cap.
Whichever cap you use, squeeze it into an oval shape so it clings to the nipple. This will keep it from falling off during recoil or handling.
CONTINUED IN PART 2
Copyright 2003 by Gatofeo. No use without permission.
"And lo, did I see an ugly cat. Smoke. Brimstone. Holes in parchment. And this ugly cat was much amused." --- The Prophesies of Gatodamus (1503 - 1566)