The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old September 24, 2002, 11:42 AM   #1
1redneck
Member
 
Join Date: July 17, 2001
Location: Boise ID
Posts: 43
310 gr. 44 loads.

I am having a heck of a time coming up with some loads for a hard cast 44 cal 310 gr. bullet.

I will be using them in a SRH with a 7 1/2 barell. I have found some in AA powders but I have a fair amount of Unique and H110 and would like to use one of those.

Thanx for any input.

good shootin
1redneck is offline  
Old September 24, 2002, 01:20 PM   #2
Boo586
Member
 
Join Date: May 15, 2001
Location: Indiana
Posts: 85
From sixgunner.com

PACO
Two loads...
Tue Mar 28 19:18:46 2000

the accuracy load in most 44s I've used is 16 grains of 2400 under any good cast bullet. Then the Keith 250 gr cast slug over 22/2400...and the 310 Lyman Keith over 18.5 grains of 2400 all in strong nickel cases...oops that's three loads...paco

look for the FAQ (frequently asked questions) and then go to favorite 44 magnum loads.

hopes this helps.

Boo586
Boo586 is offline  
Old September 24, 2002, 06:48 PM   #3
taco
Senior Member
 
Join Date: April 28, 2000
Location: USA
Posts: 936
I load several heavy weight 44mag cast bullets (260gr, 280gr, 300gr, 310gr and 325gr) for long range target shooting and hunting and use H110 exclusively. I have used several other powders but always came back to H110 because it seem to produce best accuracy and power in my revolvers. I have several friends who use VV powder with similar burn characteristics as H110 for their 44mag loads and it seems to work well. Without knowing exactly what kind of bullet you are using, I can't recommend any loads for you.
taco is offline  
Old September 24, 2002, 08:03 PM   #4
1redneck
Member
 
Join Date: July 17, 2001
Location: Boise ID
Posts: 43
Thanks for the imput.

The bullets I have are True Shot 310 gr. Wn Fp Gc made by Laser Cast. I have liked their bullets in the past and thought I would give theese a try.

Thanks again

good shootin
1redneck is offline  
Old September 25, 2002, 04:24 AM   #5
WESHOOT2
Senior Member
 
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,213
H110 OKAY

300g-n-up: AA9, N110, W296, Lil Gun, and often the best, 2400.

W296 normally very 'stable'.

Heavy crimp from Redding Profile Crimp die.
Magnum primers (test - and consider operating environment).
Work UP.

Plenty of published data.
__________________
.
"all my ammo is mostly retired factory ammo"
WESHOOT2 is offline  
Old September 26, 2002, 09:44 PM   #6
KilgorII
Guest
 
Posts: n/a
http://www.hodgdon.com/data/pistol/index.htm

They have loads for 325 grain hardcast. You should be very safe by applying that data to your 310 grain bullets.
 
Old September 28, 2002, 06:07 PM   #7
Ben Shepherd
Senior Member
 
Join Date: August 11, 2001
Location: Utah
Posts: 1,462
Out of your 2 choices H110 is the way to go. (I'm assuming you're after heavy hitters here.)
By the time unique is anywhere near H110 or AA9 velocity-wise, you peak pressures will be well into the danger zone.

Agree with WS2 on all points.

(remember he does this stuff for a living, lots of experience)
__________________
From my cold dead hands.........

NRA certified rifle, pistol and shotgun instructor.
Hunter education instructor
Ben Shepherd is offline  
Old September 28, 2002, 08:14 PM   #8
Rick R
Senior Member
 
Join Date: April 1, 2002
Location: On top of a mountain in WV
Posts: 102
I've been using W-296 with a 325gr GC/SWC and getting @1250 fps from my 6" M-629. Accuracy is good, recoil is worse. (Same load outta my 4" Mountain Gun is an adventure) I've found that I can only use the top load with new or once Winchester brass, after that things get . . . Sticky.

I'm going to try one for whitetail deer this year. I don't doubt it'll work quite well.
Rick R is offline  
Old October 1, 2002, 04:53 AM   #9
LAH
Senior Member
 
Join Date: March 22, 2002
Location: In The Hardwoods
Posts: 869
I see loads listed using a 300 gr. cast in 44 Mag. cases and 21.5 grs. of H-110.
LAH is offline  
Old October 1, 2002, 10:34 AM   #10
Steve Smith
Senior Member
 
Join Date: December 9, 1999
Posts: 4,131
Visit "Taffin Tests" of John Taffin...good info there.

http://www.sixguns.com/tests/index.html
__________________
Favor the X.


Steve Smith
NRA Life Member
Steve Smith is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:50 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08236 seconds with 9 queries