The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old September 12, 2002, 06:35 PM   #1
AlonzoMosely
Member
 
Join Date: May 14, 2002
Posts: 31
What are the possible causes of a bulged case?

Was at the range a few weeks ago. A friend was firing commercially reloaded .45 ACP 200gr SWC in a full size Baer. Don't know what powder. Heard an extra loud shot and stopped - didn't sound right. No barrel obstruction and the gun looked fine. We searched around and found the case. It was bulged at the rear where it sat over the feed ramp, and the primer was blown out. No cracks in the case. What are possible causes of this?

Seems likely it was simply a double charge, but what other possibilities are there? Bullet setback causing extra pressure? Anything else?

Thanks.
AlonzoMosely is offline  
Old September 12, 2002, 11:32 PM   #2
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 35,982
You've got the two main ones, although a double charge of most .45 ACP powders will blow the case head, too.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Old September 13, 2002, 12:08 AM   #3
blades67
Senior Member
 
Join Date: April 22, 1999
Location: Chandler, Arizona, USA
Posts: 6,014
Could've been an overcharged case, not quite a double charge, or bullet setback as you said.
__________________
Guns cause crime like spoons cause Rosie O'Donnell to be fat!

I hunt, therefore I am.
blades67 is offline  
Old September 13, 2002, 08:28 AM   #4
AlonzoMosely
Member
 
Join Date: May 14, 2002
Posts: 31
follow up

reloader has said he was having problems with "off center primer pocket reaming" [???] and that could have caused it. What does that mean/does it make any sense?

Thanks again
AlonzoMosely is offline  
Old September 13, 2002, 08:52 AM   #5
Quantrill
Senior Member
 
Join Date: February 28, 1999
Location: Arizona, USA
Posts: 725
Bulged .45 cases

If it was only one case out of 100 or so then the above answers are right in the ball park. BUT, if they all show SOME bulging, then it is time to check the barrel. I have seen a few times where someone polishes and reams the chamber of a .45acp in the hopes of feeding bullets that are difficult to feed. If too much metal is removed, the result is bulging cases to different degrees. Quantrill
Quantrill is offline  
Old September 13, 2002, 08:59 AM   #6
braindead0
Senior Member
 
Join Date: February 28, 2002
Location: Canton, Oh
Posts: 896
Off center primer pocket reaming may account for the ejected primer, but not the bulged case.
__________________
DoD# 2223
Meum scapha volitare plenum anguillae
braindead0 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:34 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06387 seconds with 9 queries