The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Black Powder and Cowboy Action Shooting

Reply
 
Thread Tools
Old July 17, 2002, 07:43 PM   #1
KenF
Member
 
Join Date: April 29, 2002
Location: Texas
Posts: 29
Cap 'n Ball Revolvers: Dry Loading ?

I haven't done this yet, but just in case...........what if I forget to put in the powder (or Pyrodex in my case) before I seat the ball ?

On the Pyrodex web site, the FAQ discusses this, saying "When it comes to dry loading (seating the bullet without putting in a powder charge) there are only three kinds of shooters. Those who have done it, those who will do it, and those who lie about it."

But it looks like more of a question about a rifle. Anyway, they say it's OK to remove the nipple, put in a bit of powder, put the nipple back, cap it up, and then blow out the ball. The only caution is to be sure the ball is seated enough to remove air space.

So what do you think? For a cap 'n ball revolver is this a dumb idea ? good idea ? better way to solve the problem ?

Thanks in advance for your help and advice.
Ken.
KenF is offline  
Old July 17, 2002, 09:06 PM   #2
Borf
Senior Member
 
Join Date: February 24, 2001
Location: Middle Tennessee
Posts: 424
Only done it twice (in rifle)
Some kits will have a little screw worm thing to go on a cleaning rod, which you can then screw into the soft lead ball and pull out.
You *may* be able to drive it out with just a percusion cap (doubtful).
Some will snap a cap, then unscrew nipple and put a few grains powder in, snap cap, etc... some folks will tell you this is a bad idea.

The BEST thing going is to get a CO2 powered hinky which fits over the nipple and blows the ball clear. Pretty inexpensive and more importantly it's safe and easy.
__________________
A great many people think they are thinking when they are merely rearranging their prejudices. -- Wiliam James

If a nation values anything more than freedom, it will lose its freedom;
and the irony of it is that if it is comfort or money it values more, it
will lose that, too.
-- W. Somerset Maugham
Borf is offline  
Old July 17, 2002, 10:55 PM   #3
WINTERVILLE WILL
Member
 
Join Date: April 6, 2000
Location: Winterville, Ga. USA
Posts: 50
1.remove cylinder from frame
2.remove nipple from dry charged hole
3.insert properly sized pin punch thru nipple port
4.drive out ball
__________________
NRA Life
SASS Life
SBSS Life
DAMFOOL #64

45-70...reach out and thump somethin'
WINTERVILLE WILL is offline  
Old July 18, 2002, 09:40 AM   #4
Alex Johnson
Senior Member
 
Join Date: February 16, 2000
Location: Grand Forks, ND
Posts: 805
I've done this on more than one occasion, not too long ago in fact. My solution is tried and true and has never failed me. First, fire any remaining chambers that are loaded. Double check the gun to make sure there are no remaining loaded chambers. Disassemble the piece and find yourself a drywall screw that is about 3-4" long. Soft lead is easy to put a screw into, I simply locate the center of the ball approximately and tap the screw a few times with a small hammer (the end of the screwdriver will work) to start the screw and than simply screw it in about 4-5 turns. After this you can put the end of the screw into a bench vice or simply use a set of vice grips to pull it out. Works every time. Only thing to watch out for is to make sure the rest of the chambers are empty and that you put the thread the screw into the ball enough turns to give it good purchase when pulling out the ball. I wouldn't recommend this method if you do have a charge behind the ball. In those instances it's best to unscrew the nipple, clean it, and place a small priming charge underneath, 9 times out of 10 this will do the trick.
__________________
I thoroughly disapprove of duels. I consider them unwise and I know they are dangerous. Also, sinful. If a man should challenge me, I would take him kindly and forgivingly by the hand and lead him to a quiet retired spot and kill him.
- Mark Twain
Alex Johnson is offline  
Old July 18, 2002, 11:05 AM   #5
Chuck Dye
Senior Member
 
Join Date: June 28, 2002
Location: Oregon-The wet side.
Posts: 878
I am with Winterville Will. My kit includes a length of brass rod for just that purpose. On one occasion when the kit was abbreviated for a hike, the deed was done with a nice dry oak twig trimmed with a pocket knife.
__________________
Gee, I'd love to see your data!
Chuck Dye is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:47 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08032 seconds with 9 queries