The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old June 26, 2002, 02:05 PM   #1
rhoss1
Member
 
Join Date: June 24, 2002
Location: West, Tennessee
Posts: 25
Cleaning Brass?

What is the best way to clean brass by hand??
Hoss.
__________________
NRA Member In Good Standing... And a CCW Permit Holder In Tennessee***
rhoss1 is offline  
Old June 26, 2002, 02:27 PM   #2
Walosi
Senior Member
 
Join Date: June 1, 2001
Location: Auburn, KY
Posts: 298
Other than a tumbler or vibe cleaner, the only productive method I've heard of (but haven't tried) is nylon mesh bags in the dishwasher. Sounds wild, but a friend swears by it.
Walosi is offline  
Old June 26, 2002, 02:31 PM   #3
foghornl
Senior Member
 
Join Date: March 18, 2002
Location: Ohio
Posts: 1,355
I've heard of the dishwasher method, but haven't tried it since I don't reload.

But I can just imagine the wife's face when she opens the dishwasher to put in a dirty cup, and sees a bag or 2 of brass
foghornl is offline  
Old June 26, 2002, 03:02 PM   #4
Redlg155
Senior Member
 
Join Date: March 13, 2001
Location: NW Florida
Posts: 2,307
I am forbidden from using household items and or utensils for anything related to shooting. This includes the use of butterknives for a screwdriver. I think the downward spiral began when I used her cupcake pan for lead ingot molds. I know its crazy..but they do make perfect ingots.

Do yourself a favor and forget trying to clean by hand. Save up some cash and buy a good case tumbler/vibrator. You will be extremely pleased by the results. Unless you are trying to clean loaded brass. Then it is very inadvisable that you use a case tumbler or vibrator. I just use a scotchbrite type of pad to remove tarnish so I can inspect old milsurp ammo better. Otherwise I shoot it as is.

Good SHooting
RED
Redlg155 is offline  
Old June 26, 2002, 03:03 PM   #5
Edward429451
Junior member
 
Join Date: November 12, 2000
Location: Colorado Springs, Colorado
Posts: 9,494
Before I got a tumbler I used to use a wooden dowel chucked in a cordless drill, slip your empty case over the end and hit it with some steel wool while it spins...

HTH.
Edward429451 is offline  
Old June 26, 2002, 03:12 PM   #6
Mal H
Staff
 
Join Date: March 20, 1999
Location: Somewhere in the woods of Northern Virginia
Posts: 14,557
Though this isn't strictly a reloading question, I'll move it to that forum since that is where folks know all about brass.
Mal H is offline  
Old June 26, 2002, 04:38 PM   #7
Bogie
Senior Member
 
Join Date: June 5, 2000
Location: Job hunting on the road...
Posts: 3,827
I use 0000 steel wool to just clean up the neck, and I pick the brass up once out of the loading block with a nylon brush (easier to demonstrate than to explain - very rapid in process). Since my "accuracy rifle" brass never hits the ground, I don't worry about the rest of it.
__________________
Job hunting, but helping a friend out at www.vikingmachineusa.com - and learning the finer aspects of becoming a precision machinist.

And making the world's greatest bottle openers!
Bogie is offline  
Old June 26, 2002, 04:42 PM   #8
Jason Demond
Senior Member
 
Join Date: May 9, 1999
Location: Hastings, Michigan
Posts: 1,845

49.97
http://www.sportsmansguide.com/showa...seq=1105873299
__________________
"ACCEPT NOTHING LESS THAN FULL VICTORY!"
General Dwight D. Eisenhower June 6, 1944
ΜΟΛΩΝ ΛΑΒΕ!
Jason Demond is offline  
Old June 26, 2002, 09:06 PM   #9
9x45
Senior Member
 
Join Date: January 14, 2000
Location: Southern California
Posts: 505
If you are only loading, like 17 rounds, then polish them by hand while watching Mayberry RFD reruns, one at a time, just like Barney. If you load for competition, like, 2,500 rounds a month, then get a good tumbler and an appliance timer. Here is my deal. Put about 500 9mm's into the tumbler with the walnut media and tumble for 4 hours. Sift media and reload with corn and polish for 4 hours. End result? Shiney and clean brass, ready to push thru the progressive. Rifle rounds are an exception because typically you are loading far fewer rounds, unless you compete in 3-gun...
9x45 is offline  
Old June 26, 2002, 11:20 PM   #10
labgrade
Member In Memoriam
 
Join Date: November 29, 1999
Location: west of a small town, CO
Posts: 4,346
Net bag & dishwasher works well enough. Best of all methods is using the dishwasher & then the clothes dryer to dry 'em out. Most certainly do the drying bit while The Wife is at home. The racket will allow her to see the wisdom of a tumbler = case solved (& cleaned).

After doing without or doing by hand for 20+ years, my (The) Wife bought me a tumbler/vibratory-type cleaner for somethingor'nother .... well worth it. Dump the brass in, turn it on, walk away for a while, come back, sift it out & go. Good deal!

Hmmmm, rereading that last makes me do an obligatory clarification. I never went without or had to do it by hand regards anything other than cleaning brass .... lest there be some mistakes - intended or otherwise. Youse guys!

Grab yourself a tumbler. Even the ones that don't take more than 100 or so 9mm cases are still well worth the savings in time & hassle.

If bucks are way tight, you just can't justify a tumbler, wash 'em up only as you think they need - brass does work quite well when tarnished & all but really filthy - & make really sure the brass is dry, dry, dry. Priming & dumping powder into a damp case isn't the best of all worlds .....
labgrade is offline  
Old June 27, 2002, 01:48 PM   #11
db4
Member
 
Join Date: December 8, 2001
Location: Oregun
Posts: 53
Bucket of hot water and dish soap, stir vigorously with a stick, rinse and airdry and they are plenty clean enough to reload.

Disadvantage to this method is with autoloader cases that you have to pick up off the ground; over time the brass assumes the color of...the ground.
db4 is offline  
Old June 27, 2002, 03:34 PM   #12
Pampers
Senior Member
 
Join Date: October 7, 2000
Location: In the Lost State of Franklin
Posts: 482
Cheap Redneck Way

Git yerself a large plastic mayo jar from yer favorite hash house. Git some RCBS Liquid Case Cleaner. Mix accordin to instructions. Put brass in mayo jar and cover with cleaner mix. Put the jar in the bed or floorboard of yer pickup. By da time you git home dis evenin, yer brass'll be clean! Cheap! ... Crude! ... Effective!
__________________
Your Most Humble & Obedient Servant
Fred J. Drumheller
NRA Life
NRA Golden Eagle
Pampers is offline  
Old July 1, 2002, 01:30 AM   #13
uglymofo
Member
 
Join Date: August 1, 2001
Posts: 72
A really great cheap reusable cleaner is white vinegar. 99 cents / gallon at Safeway. Thirty seconds' immersion and a water rinse to kill the acid process and they're done.
uglymofo is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:11 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09191 seconds with 9 queries