|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Search | Today's Posts | Mark Forums Read |
|
Thread Tools | Search this Thread |
April 12, 2024, 07:23 AM | #1 |
Member
Join Date: April 4, 2024
Posts: 37
|
What's the best way to break in a new pistol?
Below is what I heard:
1. Wipe off all the factory grease, which is designed for rust prevention instead of lubrication. 2. Lube the slide channel. 3. Shoot a few hundred rounds, using 124 gr bullets. What else? Does dry-firing help? |
April 12, 2024, 07:57 AM | #2 |
Senior Member
Join Date: March 8, 2001
Location: Deep South Texas
Posts: 1,683
|
Clean lube, shoot. What type bullets depends on the gun.
The reality is that what you are breaking in is the user. It takes a few hundred rounds to initially get proficient with a new firearm.
__________________
To be vintage it's gotta be older than me! |
April 12, 2024, 11:49 AM | #3 |
Member
Join Date: April 4, 2024
Posts: 37
|
|
April 12, 2024, 05:47 PM | #4 |
Member
Join Date: October 23, 2021
Location: Deep South
Posts: 74
|
|
April 12, 2024, 08:39 PM | #5 |
Senior Member
Join Date: March 21, 2012
Location: Indianapolis, IN
Posts: 4,014
|
Read your manual, see if and or where it says to put oil, not just the slide channel. sometimes its the barrel or other places.
More of a concern with rifles, but its advisable to run a lightly olef patch down the barrel to clean out and debri or machining /protective oil from the inside of the barrel. Clean it Oil it Shoot it Most modern pistols do not need to be broken in, unless you bought a high dollar competition gun that is fitted very tightly. But cleaning the gun, and shooting it to make sure its working properly is reccomended.
__________________
I don't believe in "range fodder" that is why I reload. Last edited by Shadow9mm; April 12, 2024 at 10:15 PM. |
April 12, 2024, 09:21 PM | #6 |
Senior Member
Join Date: September 8, 2007
Location: Mississippi
Posts: 16,198
|
Before you do anything tear it completely down and clean off all the packing grease. Oil it up and shoot it.
|
April 12, 2024, 10:28 PM | #7 |
Staff
Join Date: February 12, 2001
Location: DFW Area
Posts: 25,049
|
Read the manual. Guns aren't all the same. I've learned a lot about guns just reading manuals.
Field strip and clean. During that process:
Shoot it. I've not had issues with ammo preference (in terms of bullet weight) during break-in with centerfire guns, but rimfires may want to be broken in with certain types of ammo. Sometimes a gun will have some hiccups the first time to the range. I have one pistol where each of the magazines had a weird malfunction the first time they were loaded/shot. The rounds would bind in the magazine and cause a jam. Then they never did it again. That kind of thing is somewhat unusual, but still, I wouldn't freak out if there were some minor issues with the very first time the gun was shot. Then take it home and repeat the strip and clean. Check for excessive wear, to see if anything changed, and then reapply lube where applicable based on the manufacturer's guidance and based on where you see wear. Next time at the range I wouldn't expect to see any malfunctions. Not sure exactly what you mean by the "slide channel", but if you mean the firing pin channel, don't put any lube in there. If you have a dry lubricant, you can apply some to the firing pin channel sparingly, but usually firing pins don't need any lubricant.
__________________
Do you know about the TEXAS State Rifle Association?
|
April 13, 2024, 12:38 PM | #8 |
Staff
Join Date: March 11, 2006
Location: Upper US
Posts: 28,944
|
Fine advice, though I would raise two points...
Often a beginner will have no idea what is, and isn't "excessive". At metal to metal contact points, the finish (blue, or whatever) will get worn off. A degree of this is normal and not excessive. My other point is, that most people who aren't well versed in the terminology think of the "slide channel" as being where the slide fits over (or inside, depending on design) of the frame rails. Field strip, clean, and properly relubricate is also sound advice for any used (but new to me) gun. This gives you a "clean slate" starting point for evaluating how the gun performs.
__________________
All else being equal (and it almost never is) bigger bullets tend to work better. |
April 13, 2024, 08:52 PM | #9 |
Member
Join Date: April 4, 2024
Posts: 37
|
Many thanks for all the excellent advice.
|
April 15, 2024, 11:28 AM | #10 | |
Senior Member
Join Date: July 29, 2010
Location: The ATL (OTP)
Posts: 3,948
|
Quote:
__________________
A major source of objection to a free economy is precisely that it ... gives people what they want instead of what a particular group thinks they ought to want. Underlying most arguments against the free market is a lack of belief in freedom itself. - Milton Friedman |
|
Thread Tools | Search this Thread |
|
|