PDA

View Full Version : A Kitchen Table 870....


Dave McC
January 11, 2001, 08:37 AM
I thought I had posted this before,but I cannot find it in the Archives. So....

Back around 93 or so, I entered Guns R Us with the intent of getting some minor repair done. A short conversation with the gunsmith( a longtime friend) ensued during which he mentioned that they had received a massive amount of firearms from the inventory at the Md Pen and would be shortly selling them.Since I was then working for the Md Prison system, my ears perked up. He mentioned that some 870s were pretty bunged up(no surprise) and they would be parted out. He then threw in a zinger, they were getting some receivers "Parkerized" with a phosphate finish and selling them separately. Price was $65,and included no separate parts but the stock bolt. Little wheels in my head started turning as I mentally inventoried all the leftover 870 parts at Casa McC, and I realized I could put together an inexpensive turkey gun w/o bending the budget all that much.

A little haggling, a bit of whining and begging, and I had the parts I needed coming my way. Besides the receiver, I bought a trigger guard/group for $20, the forearm metal, and they threw in the worst, ugliest, most abused piece of stock wood in Md, probably just to get it out of eyeshot. I had everything else, including a matte finish 870 bbl shortened to 21" and threaded for Colonial tubes, with a lengthened forcing cone.

As a favor, the trigger group went through ultrasonic cleaning and relubing before I picked it up.

So, during some down time at home, I sat and put together my Frankenstein shotgun. I'd fiddle with it a bit, then leave it alone, but still managed to assemble it within a week. I wanted a fairly light shotgun for turkey, upland hunting, etc, and did some mods to lighten it a bit.

First, since a lot of weight left with the other seven inches of bbl, I hogged out some wood from that ugly stock to move the balance point forward. Then, the wood got spray painted flat black, two coats with light 0000 steel woolling first and in between. A couple spacers were added between the stock and pad(Remington standard) to lengthen the stock to about 14 1/2".

Then, I lightened the front end by shortening the large nut that holds the forearm wood and metal together,and handfiled new notches before reassembly.All metal parts got the moly grease treatment before assembly.

Using the bolt from my oldest 870,which had been Flextabbed, I put together the action and found I had an acceptable slap trigger, and little slop.The original mag spring, mag cap with sling swivel stud from that oldest 870(ca 1956) and a plastic follower completed the package, and I put it all together and stood back to admire it.

That didn't take long. The contrast between the phosphate receiver, the blued secondary metal and the matte finish barrel wasn't pretty. I reminded myself that cheap beat pretty sometimes and headed for the institutional range. I took along some tools and aluminum foil.

Setting up a patterning target at 15 yards, I used the foil to shim the stock until I had more of the pattern over the bead than under it. I then repeated this at 25 yards and liked the results.Switching between Extra Full and Skeet I tubes gave the same POI, so I knew I was "ON".

The Lt running the range was interested in the project and when I was done patterning, he broke out the trap and some clays. With both of us shooting, a box of 8s and some white flyers went to show that the gun worked well, and shucked smooth. The toe of the pad did need a bit of rounding, but that was the only glitch. I did reduce the weight of the mag cap by sanding it flat and cold bluing it, but that was just a bit of nitpicking about the balance and swing. A Redneck Jamboree shoot held at a friend's Eastern Shore hunt club a month later showed me,and varied onlookers, that I had a pretty good GP shotgun that should serve for anything flying.Since then, I've killed lots of clays, some dove, pheasant, quail, geese, and the odd ground game with it.

In summation:

I'm no gunsmith, but most of this doesn't call for a smith.
870s can be taken apart like Erector Sets,and mixing/matching of parts isn't hard, nor dangerous. According to Remington, all 870 parts interchange within gauge. Caveat, since the 870 has been around since the early 50s, some parts out there may be worn past use.

Total cash outlay was about $140, but that doesn't account for the bbl.

And it was fun....

Dave R
January 11, 2001, 04:49 PM
Great story. Sounds like a lot of fun. Bet you're pretty attached to Frankenstien now, with all the work & tuning you pout into it.

Dave McC
January 11, 2001, 08:33 PM
I've built all three of my 12 gauges, to some degree. And I'm attached to them, they are good tools that I've more or less molded to a specific purpose.

Later this week, I'll find out if I'm invited to a snow goose hunt in February, and a buddy said something about a preserve pheasant/chukar hunt. And I may squander some cash at a rtange doing 5 station or clays.

On all three, I'll use Frankenstein....

Postman
January 11, 2001, 08:42 PM
Dave,

I grew up in Maryland. Back in the day, my father used to frequent National Sporting Goods in Baltimore. Before I moved to New York, my shop of choice was The gun rack in Burtonsville.

Ever visit either?

Living in a terribly gun unfriendly state I miss the well stocked gun stores of Maryland.

DML
January 11, 2001, 11:19 PM
The only two parts that can't be replaced by the average person on an 870 are the ejector and the magazine tube. Even the ejector can be relaced by anyone with a little knowledge of tools beyond a screwdriver. The magazine tube is silver brazed to the reciever and is a factory job.

Dave McC
January 12, 2001, 08:35 AM
Postman, the Gun Rack is but a few miles away,and I patronize it on occasion. I might do it more, but they've few used guns, and that's my favorite way to fly.

The two gun shops I do use and have for over 20 years I refer to collectively as Guns R Us, and they are Valley Gun Shop, on Harford Road north of B-more, and Clyde's Sports Shop near Arbutus. Both are great places run by good people.
Valley has more LE and military style stuff. Others I like but do not use much for varied reasons, including distance, include Duffy's Gun Room out near Butler,The Gun Shack in Mount Airy, and On Target in Severn. There's others I do NOT like, but I'll leave them alone.

The 870 in this thread was from Valley.

DLM, if I can do it, anyone this side of paralysed can. "Tool Challenged" is the term.