Powder flask recommondations?

[bigminnow]

I have been looking at powder flasks. I'm getting tired of scooping powder from the container and its probably not the safest way...

I've looked at a lot of websites and they all seem to have the same stuff...but I'm a function over form type person first and I don't really need an ole time style powder flask that may or may not work well.

Anyone seen any great functioning powder flasks out there and care to point me in the right direction?

I found this one...it even says it is made in the US so I called them and the person that answered the phone sounded very foreign and said they did not have any and did not know when they would have them again because they got them out of Canada...hmmm...made in the US?? ...anyway, I thought it might work well so if you know where one might find something similar, pass it on...thanks...

http://muzzleloadingbullets.com/muzzleloader_powder_measurers.html

[Lee McNelly]

have u tried track of the wolf

[bigminnow]

No but I will check it out now...I might use some of my pill bottles for the time being. Lord knows I have lots of them in all sizes!

[Lee McNelly]

what u r looking for is what i settled on the large brass flask w several spouts

[bigminnow]

Thanks for the website info Lee...this is just what I was looking for. How does the large brass flask work? This is what I will order. Thanks...

[Doc Hoy]

I like the CVA 1400.

http://www.rrarms.com/catalog.php?prod=CVA1400

That is by far the best price I have ever seen on it. Shipping is a little steep at over $11.00. I think, even considering that the deal beats Cabelas.

You get get good deals on used ones on eBay now and again.

[madcratebuilder]

That's a very nice flask/measure you are looking at bigminnow, I don't think you could find a better combination. It may not be a easy to use as the standard single spout style with a thumb lever. Then there's the Walker style with the push spout. I find the thumb lever the quickest to use, you can get different size (volume) spouts for them.

[Rifleman1776]

I hope you are not planning on loading directly from the flask.
That is a very dangerous practice.

[Noz]

Look at the TRESO model at the Possible Shop.

Watch for dead horses along the way.

[robhof]

It's not hard to make your own, I got all the parts on Ebay including the horns.:D

[Pahoo]

I hope you are not planning on loading directly from the flask.
Yes, I suspect some are, especially for C&B revolver use and even though I have done so, it is increasing the potential of you getting hurt. I rarely do this and never instruct it as being an option. ..... ;)

I like the CVA 1400
Basically I like this style with the swing gate but also have one of the push buttons types like the OP listed. I have found that in time, the push button types, start to hang up with powder dust where the gate types do not. I also have the smaller field size of the 1400 that I take in my hunting pack. I have various spouts that go onto the 1400. ... ;)


Be Safe !!!

[kwhi43@kc.rr.com]

Here what I use. A cut off can and a spout that opens and closes automatic.
http://i119.photobucket.com/albums/o127/prizzel/AutoCan.jpg

[Pahoo]

Here what I use. A cut off can and a spout that opens and closes automatic.
However, you are also using a calibrated measurer to pour into; RIGHT ???

If Not;
Classic example of what I won't instruct or use. There are safer and better options out there. More than my humble opinion and no disrespect intended. ... ;)


Be Safe !!!

[Fingers McGee]

I use a flask like this - mine is silver plated - to charge my revolver cylinders. High quality flask that accepts a variety of premeasured spouts - and looks good too.

http://i25.photobucket.com/albums/c86/fingersmcgee/flask-flore_1.jpg


YMMV

[OutlawJoseyWales]

Big Minnow,
I've got all the different kinds, well except that "special" one that kwhi43 has. :eek:
But, frankly I like the model that you've shown, for me it's faster and I don't drop powder all over the place.
OJW

[H.W. French]

Track has pretty much whatever you you need so far as flasks, spouts and funnels. The brass funnel is key for refilling those small pistol flasks. Be sure to add one of their handy graduated powder measures as well. I also use a Thompson Center "see-thru" flask for the rifle at the range.
French

[kwhi43@kc.rr.com]

The can I use is safe enough on the National range at Friendship and all the
big shoots here and in Iowa. As a matter of fact, it's just about what everybody uses.

[Pahoo]

However, you are also using a calibrated measurer to pour into; RIGHT ???
I don't have a problem with your can and really like that spout. I'm not questioning that, just the application and use. .... :confused:

Be Safe !!!

[kwhi43@kc.rr.com]

Mykeal, your turn.

[zullo74]

Phil,

Don't forget arcticap. He'll chime in here to dump on you in a little while too.

[orangello]

Well, i guess i would look like a bum dumping my loads out of used .45ACP or .357 magnum cases, but it works OK for me.

[Hawg Haggen]

I use one like Docs and I have a couple of old TC measures.

http://i7.photobucket.com/albums/y269/rebel727/bp%20stuff/100_0844.jpg

[mykeal]

Just finished some of SWMBO's strawberry shortcake and must have dozed off for a bit....

NMLRA Range Rules and Regulations, May, 2010 edition:
Rule number 1220-Powder Measure-A separate powder measure or holder will be used to carry the powder charge from the container to the muzzle of the gun. Charging directly from the horn or flask is unsafe and is not permitted.

Phil (kwhi43@kc.rr.com) follows this and all other safety rules and regulations.

[Hellgate]

Bigminnow,
I use either the Remington style flask as illustrated by Fingers McGee or the cylindrical flask as shown by CVA. Both work fine but the Remington flask of Fingers holds about 50% more powder. The cylindrical flask will throw 60 charges of 20grs each. I always load from the flask but I am shooting Cowboy Action matches and there is plenty of time to let any embers burn out. Loading from the flask is dangerous when loading rifles or shotguns but not so much in the short chambered revolvers we use for CAS.

[bigminnow]

I should have mentioned that my flask use will be for revolvers only...I really enjoy shooting the revolvers. I have 5 at this time including the 1858 Pietta Remington type from Cabela's and I ordered another one today. I must be infected with black powder or something huh. This is my last one unless...I sell, swap, trade a brass frame model for a steel frame.

So, if I'm careful, what do you think about loading directly to the revolver cylinder? I know there is always the possibility of a horrible accident and I would never load a long rifle directly from the powder horn/flask. I also started using a loading jig that I bought. Have to remove the cylinder but I like doing that...

Right now I'm using a Lee's 1.3cc scoop and I scoop from a container and pour into the cylinder using a funnel...and I could keep scooping I guess. Anyway, Track of the Wolf has a lot of pieces, parts, and complete flasks. Gee I guess I need one for each revolver now huh? :D

[Lee McNelly]

use the same flask and have say two spouts one for each revolver or spec charge

Hi minnow

[Fingers McGee]

I should have mentioned that my flask use will be for revolvers only...I really enjoy shooting the revolvers. I have 5 at this time including the 1858 Pietta Remington type from Cabela's and I ordered another one today. I must be infected with black powder or something huh. This is my last one unless...I sell, swap, trade a brass frame model for a steel frame.

So, if I'm careful, what do you think about loading directly to the revolver cylinder? I know there is always the possibility of a horrible accident and I would never load a long rifle directly from the powder horn/flask. I also started using a loading jig that I bought. Have to remove the cylinder but I like doing that...

Right now I'm using a Lee's 1.3cc scoop and I scoop from a container and pour into the cylinder using a funnel...and I could keep scooping I guess. Anyway, Track of the Wolf has a lot of pieces, parts, and complete flasks. Gee I guess I need one for each revolver now huh?

One can never have too many C&B...........or flasks either for that matter

IMNSHO, loading a revolver directly from a flask is perfectly fine.

[mykeal]

Buy a variable powder measure and use it - fill it from the flask. It works.

[DG45]

Cabela's is selling a Pedersoli Tubular Powder flask (Item IK-212239) for $27.99. Photo's of it look just like the CVA 1400 mentioned earlier on this thread that's selling for less, $16.77 I think it was, but the poster said that the CVA shipping cost was $11.00.( I think Cabela's charges $8.95 for 3-6 day delivery on orders between $25.00 and $50.00. Not sure about that though.)

Cabelas is also carrying a Pedersoli Powder Flask Spout Kit (set of 6) for $21.99. I don't know if they'd fit the CVA 1400 or not.

If you need a lot of other stuff too, Cabela's presently has coupons for $20.00 off on orders over $150.00. Sometimes they have special shipping deals too. The best I've seen was a $5.00deal. Don't know if there is any special deal on shipping right now though.

[Doc Hoy]

....fit the CVA 1400.

[bigminnow]

I guess I'll end up with probably three flasks and associated gear with them...
Sorta like my clothes...
I have my everyday work clothes and then Friday night go out and have fun clothes and Sunday go to meeting clothes...yaaa, looks like I'm going to need several powder flasks...yep...

[kwhi43@kc.rr.com]

One flask, different size spouts.

[Hawg Haggen]

One flask dedicated measures.

[Doc Hoy]

...and Hoy's telescoping variable measure.



:D

[arcticap]

Phil,

Don't forget arcticap. He'll chime in here to dump on you in a little while too.

I haven't seen one of those gravity spout covers since I poured shots of liquor when I was a bartender in college!
I'm glad that it works but it doesn't seem to be very moisture resistant and should probably be switched with a screw top after shooting. It may also allow the powder to spill out if the can is tipped over. :)

My favorite is the Traditions brass push button flask because I like to push with my thumb for precision and it's the most comfortable for me to hold:

Traditions Accessories - Low Prices With Free Shipping!

http://www.thehighroad.org/showthread.php?t=608328

[bigminnow]

Looks like I'm going to have a couple of flasks anyway. I want to try the push button and the lever type flasks. I can let my brothers use the one I am not using at the time. :) I might even make a real cheap one from a plastic pill bottle. Thanks...

[mykeal]

Hmmm. I was going to ask Phil to put me in his will to inherit those chimney covers when he was done with them....;)