PDA

View Full Version : need browning bar disassembly instructions


jbrown
September 12, 2006, 08:47 PM
I nee to disassemble a bar and clean it.

Steven Mace
September 13, 2006, 01:42 AM
jbrown, it this the Browning BAR you're talking about?

http://www.stevespages.com/pdf/browning_bar.pdf

Steve Mace

jbrown
September 13, 2006, 11:43 PM
Harley sent me some instructions last year that were more detailed and complete disassembly,and ,it is for an original bar,not the newer version.i had to get a new computer and lost the file he sent me.Thank you for helping out,steve.

T. O'Heir
September 19, 2006, 10:30 PM
"...an original bar..." As in the light MG?

jbrown
September 22, 2006, 08:48 PM
no the original browning bar semi auto sporting rifle.the link provided was for a mark II

jbrown
September 23, 2006, 12:14 PM
thank you!

Metaloy Industries
September 23, 2006, 01:09 PM
You can go to Brownells website, click on schematics, click on the Browning icon and it should show The BAR as an option. Note: I have no personnel experience with the BAR but be careful. They can be a bear to disassemble and reassemble. Very difficult.

Wildalaska
September 23, 2006, 01:24 PM
If I were you I would take it to a Browning service center, BARs are a pain.

WildweknowwehavedoneenoughofthemAlaska

jbrown
September 25, 2006, 05:15 PM
I have had one apart already.I just needed the directions that I lost on my old computer,back from harley.with those it is all spelled out and not that difficult to do.I wouldnt want to try with out them,however.

T. O'Heir
September 26, 2006, 12:28 AM
Ok, but the real original BAR is more fun. This help at all? Stevespage seems to be down. http://www.bowtools.com/Articles/Gun_Manuals/browning_long_short_trac.pdf
Or this one.
http://media.browning.com/pdf/om/bar_98355_om_s.pdf

Kid Kwik
October 8, 2006, 12:58 AM
Mine does not have two pins holding in the trigger group. This one is close to 40 years old.
I grew up in AK and my father shot a moose almost every year with this 7mm Remington Magnum Belgian BAR. I have inherited it and a 30-06 version of the same rifle.
I have the pdf files from browning but none of them seem to have the model that I do.
I can get it fairly clean but I can not figure out how to get the bolt out. I know it will seem really obvious when someone tells me how to do it.

Thank you in advance for your help.

jbrown
October 9, 2006, 09:38 PM
send me your email and I can forward it to you

Kid Kwik
October 13, 2006, 01:44 AM
Hello JBrown,
I sent you a PM with my email address.
Thank you,
KK

brownie42
March 23, 2007, 03:46 PM
I have the same rifle and also need the disassembly instructions, if they are still available. Thanks.

--Bill

washdave
December 7, 2008, 03:28 PM
I too need the instruction for that model bar. My email is washdave@aol.com thank you very much. I have everything off but cant get the bolt out and it seem stuck to the triger assembly.

akadiesel
April 25, 2009, 08:29 PM
Took forever to find this ...

http://www.midwestgunworks.com/field_service_manual/browning_bar_fsm.pdf