April 22, 2010, 02:36 PM | #1 |
Senior Member
Join Date: July 19, 2007
Posts: 332
|
Good screwdriver set
What have you found to be the best smithing set? I need a good set before I can start doing some work on my C&R rifles. Sarco has the Grace smithing set 28.00 for 8 drivers; then there's also the B-Square and Wheeler sets. What do you recommend? Thanks.
|
April 22, 2010, 02:43 PM | #2 |
Senior Member
Join Date: January 23, 2008
Posts: 713
|
wheeler has 2 sets. the larger one has more star and hex bits. the smaller set is all you really need. saw one on ebay for 50 bucks. been using one for 5+ years without any problems
__________________
http://takdriver.com/ |
April 22, 2010, 02:46 PM | #3 |
Senior Member
Join Date: September 15, 2009
Location: Phoenix, AZ. 30 miles from water, two feet from Hell.
Posts: 355
|
I use them both. there great.
|
April 22, 2010, 02:58 PM | #4 |
Senior Member
Join Date: August 19, 2007
Location: Montmorency Co, MI
Posts: 1,551
|
I recently purchased the 'Chapman' sold by most of the big 4
|
April 22, 2010, 03:20 PM | #5 |
Senior Member
Join Date: March 12, 2006
Location: SE Wisconsin
Posts: 285
|
Brownells Magna-Tip.
Bruce |
April 22, 2010, 04:06 PM | #6 |
Member
Join Date: February 18, 2010
Posts: 65
|
Snap-On
__________________
TSR80 - Firmly seated in reality. Basing conclusions on emotions is like wiping before you poop, it doesn't make any damn sense. |
April 22, 2010, 06:26 PM | #7 |
Senior Member
Join Date: June 23, 2004
Location: Ohio
Posts: 5,676
|
I have a Chapman kit, the little red box, but it is of limited use as it has nothing for narrow slots. I went to Brownells to get the 3 Apex type bits made for S&W revolvers, thereafter I eventually got one of their big kits. Well it is not all of the possible bits. It is sort of intermediate as it skips some sizes but is vastly more useful than the Chapman kit. Has all different widths and blade thicknesses for those narrow slots that you better fit right. While you are at it with Brownells you might get a kit of punches for round head pins and the ones for hollow roll type pins, those are quite useful sometimes. Buggered up pins can be as bad as a buggered screw head.
__________________
Your gun is like your nose, it is just wrong for someone else to pick it for you! |
April 22, 2010, 06:44 PM | #8 |
Senior Member
Join Date: May 4, 2001
Posts: 7,478
|
For quality and the number of sizes of bits that are available, the Brownell's Magna-Tip is the best.
These are a true professional quality set, made of the finest materials. The bits are deliberately made hard so usually the bit will break, not an expensive and hard to get gun screw. An advantage is, if you break or damage a bit, all you have to do is email Brownell's and they'll send you a new bit free. I recommend buying a set with the Law Enforcement size handle. This is the perfect size for good control. The standard handle is too big, and the stubby is too short. |
April 22, 2010, 08:27 PM | #9 | |
Staff
Join Date: November 28, 2005
Location: Montana
Posts: 9,443
|
Quote:
Wheeler's set has impressed me enough to buy. No disappointment so far.
__________________
If it were up to me, the word "got" would be deleted from the English language. Posting and YOU: http://www.albinoblacksheep.com/flash/posting |
|
April 22, 2010, 11:11 PM | #10 |
Junior member
Join Date: February 2, 2008
Posts: 3,150
|
The Grace drivers used to be very nicely made but the last set I ordered came in with every drivers tip having non parallel sides. I sent them back. I think they're importing them now from Asia. The Chapman sets are pretty good for the price. If you want to just start at the top of the line buy Brownells Magna set. I have a box full of bits from the hardware store that I ground to perfectly fit a screw and then never needed that size again. You'll get very good and custom fitting bits to your work. You will never have enough bits or the right size. There seems to be NO world standardization of screw slots. Huge +1 on the Law Enforcement handle. That's all I use anymore.
|
April 29, 2010, 09:02 AM | #11 |
Senior Member
Join Date: November 29, 2004
Location: South Carolina Lowcountry
Posts: 103
|
I've got the bigger Wheeler set and have used it on a couple repair jobs and one build thus far. Seems to be a great product for the money.
|
April 30, 2010, 05:57 PM | #12 | |
Senior Member
Join Date: July 7, 2008
Location: Upper midwest
Posts: 5,631
|
Quote:
This was a big disappointment. And of course the one that broke was the most useful size.
__________________
Never let anything mechanical know you're in a hurry. |
|
April 30, 2010, 07:21 PM | #13 |
Senior Member
Join Date: June 16, 2008
Location: Wyoming
Posts: 11,061
|
Rule of Thumb:
The higher quality, and more expensive the Screw driver set, the faster your kids or grandkids will screw up the tip or leave them out in the rain. A good quality gun screw driver set needs to be locked up in the safe with your best guns.
__________________
Kraig Stuart CPT USAR Ret USAMU Sniper School Distinguished Rifle Badge 1071 |
May 1, 2010, 04:20 PM | #14 |
Member
Join Date: May 17, 2004
Location: Mountains of East TN
Posts: 35
|
Check with Brownells
__________________
Cummings Custom Refinishing Offers Quality Craftsmanship at Affordable Prices Fully Licenced FFL for over 20 years www.ccrrefinishing.com 423-639-8924 |
May 1, 2010, 04:25 PM | #15 | |
Senior Member
Join Date: May 27, 2007
Posts: 5,261
|
Quote:
|
|
May 1, 2010, 04:28 PM | #16 | |
Senior Member
Join Date: July 7, 2008
Location: Upper midwest
Posts: 5,631
|
Quote:
And not just screwdrivers. A friend who's a professional woodworker told a story about the time his wife asked him, "Honey... Why do you keep your screwdrivers so sharp?" She was trying to drive a screw... with a paring chisel.
__________________
Never let anything mechanical know you're in a hurry. |
|
May 1, 2010, 04:52 PM | #17 |
Senior Member
Join Date: November 13, 2009
Location: South Carolina
Posts: 162
|
thanks for the great info!
My father and I have been pondering the same issue (quality smith drivers). Anyone ever used/seen/heard of brass drivers? Any good/useless?
__________________
In the land of the blind, the one-eyed man is king. -T.W. |
May 1, 2010, 08:11 PM | #18 |
Senior Member
Join Date: May 4, 2001
Posts: 7,478
|
Brass drivers are useless for gun work.
The idea is that brass won't damage the slots, but the truth is, the soft brass deforms, slips out, and damages the slots. A properly made, high quality gun screwdriver won't damage the screw since it fits the slot properly and puts all the pressure on the sides of the slot. A good gun screwdriver should be so hard that if you over stress the screw the driver will break. This is by intent. It's much cheaper, faster, and easier to replace a screwdriver bit than an expensive, and possibly unobtainable gun screw. |
May 2, 2010, 07:44 AM | #19 |
Senior Member
Join Date: November 13, 2009
Location: South Carolina
Posts: 162
|
Many thanks Dfarisheel.
I'd always wondered about the softness of brass for this purpose. Will avoid brass and go with some of the quality sets mentioned here.
One more question while we're on the screw topic or at least nearby--any gun blue-friendly breakaway products been good for anyone? We've always used PB (parts breaker) in the squirt or aerosol can but not for guns. Has anyone had good luck with other products for firearms application? I'd like to know before I need it!
__________________
In the land of the blind, the one-eyed man is king. -T.W. |
May 2, 2010, 09:31 AM | #20 | |
Senior Member
Join Date: August 6, 2006
Location: Middle of Nebraska
Posts: 944
|
Quote:
__________________
I reject your reality and substitute my own. |
|
|
|